
Please note that sgnal audo boost should be used on a temporary or as-needed bass because t wll not only boost the target sgnal audo but
t wll also boost the loudness of ground nose and false sgnals. Therefore, t s recommended to keep the swtch at poston 1 and turn t to
poston 2 or 3 only when you want to verfy a weak metal sgnal and then turn t o agan.
SIGNAL AUDIO BOOST
The sgnal audo boost swtch boosts the sound of weak sgnals receved from small or deep metals makng t
easer for you to detect those uncertan targets.
At poston 1, the booster s o. At 2, the sgnal audo wll be hgher and at 3, t wll be heard at ts maxmum.
SIGNAL AUDIO
To avod mssng smaller and deeper targets, sweep the search col both from rght to left and left to rght over each area you are scannng,
slghtly overlappng the sweeps as you move forward.
When the devce detects metal, t wll produce an audble tone.
The devce has 3 tone audo dscrmnaton. The lower tone s for ferrous metals. For non-ferrous metals and gold, the devce produces 2 very
smlar hgh tones. In case of alloy detecton the devce may produce a hgh-low double-tone sound. In order to get famlar wth the
derent tones of your devce, t s recommended that you practce wth derent types of metals and dentfy the sounds before you use t
out n the feld.
NOTE: Dscrmnaton, just lke n any other metal detector, may not always be 100% accurate. There are many derent factors aectng
dscrmnaton accuracy. All metals based on ther conductvty, shape, orentaton underground, depth and ground mneralzaton are sensed
derently by a detector. Oxdzed metals bured under ground for a long tme such as tnplates and tns may produce gold lke sgnals.
Followng the experenced metal detector users' rule of thumb "when n doubt, dg" s the rght thng to do.
SEARCHING AND METAL DETECTION
After the settngs are adjusted, you can start searchng by lftng the search col 5cm. above
the ground and sweepng t rght and left, keepng t parallel to the ground.
The devce operates on the prncple of moton. Ths means that you must move the search
col over the target or the target over the search col, n order for the devce to see t. In other
words, metal detecton s not possble wthout movng the search col.
Coil cover use is optional. It protects the search
coil from scratches. If you want to use the cover,
attach the cover to the coil and press firmly on
the edges to secure.
Holding the metal pin pressed, insert the S-rod
into its place underneath the system box and
secure it by tightening the wingnut as shown in
the picture.
Again by holding the metal pin pressed, insert the
upper shaft into the S-rod and click the pin into its
hole. Then, secure it by tightening the twist lock.
Insert the extension shaft into the upper shaft
holding the metal pin pressed and adjust the
height by clicking the pin into one of the holes.
Then, secure it by tightening the twist lock again.
You may use the battery by attaching it to your
waistband as shown in the picture or to the side of
the system box using the optional battery case.
ASSEMBLY
Place the washers into the openings on both sides
at the end of the extension shaft. After placing the
shaft on the coil as shown in the picture, insert the
fastening screw through the hole and tighten it
using the wingnut.
Wrap the coil cable around the shaft all the way up
as shown in the picture and after inserting it in the
coil input socket underneath the system box,
secure it by twisting the connector. Pay attention
to not wrap the cable too tight during this step.
Plug the battery cable into the battery input socket
underneath the system box and tighten securely.
Assembly is completed.
Kommentare zu diesen Handbüchern